Boost Cooling

Sort By:  
Snow Performance Stg 2.5 Boost Cooler F/I Prog. Water / Meth Injection Kit (Snow210)
Unlock 50-70 HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2.5 Boost Cooler™ water methanol injection kit is available for all forced induction applications (Supercharged/Turbocharged).

The Stage 2.5 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less water methanol according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives a accurate delivery of water methanol and allows cooling and performance improvements over a wide range for improved drivability. Especially helpful for direct injected engines to remove 100% of carbon build up on the valves. Recommended for all street/strip driven forced induction vehicles using a turbo or centrifugal supercharger (Procharger/Vortech) looking for cooling over a wide range. 


The VC-50 (ISO 9001 Manufactured) controller offers the functionality of a boost gauge and water methanol controller all in one! Highlighting a bright 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) O-LED screen displaying boost, percentage of injection, low level, secondary stage activation, prime button, and system fault codes directly on the screen. You can tailor the controller color to match your OEM gauges or mix and match up to two colors!

This kit utilizes the only OEM approved water methanol injection pump on the market with proprietary heat flange, twin seals, and custom motor winding to run cooler and longer than the competition. The Extreme Environment™ 300 PSI UHO pump is designed to be in the elements with O-Ring connections that are then sealed and potted at our Colorado facility to ensure no moisture can enter the pump internals. Compare this to pumps that use a pump "sleeve". These sleeves will keep moisture around the pump unit leading to corrosion as well as trap heat greatly decrease pump life. The Stage 2.5 comes standard with 100% methanol resistant components using stainless steel, nickel plating, EPDM, and hard anodizing to ensure years of continued use. Tie that in with new Snow Performance ACU-SEAL™ compression fittings for guaranteed leak free operation even when using 100% methanol. Whether running a supercharger, turbo, or high compression motor the Stage 2.5 Boost Cooler™ will make the induction charge colder, denser, and increase 91 octane fuel to 116 octane race gas levels allowing full power all the time! 

Features: 
  • U.S.A. Made
  • Adjustable Progressive Water Methanol Engagement & Monitoring
  • Digital Boost Reading (1-50 PSI)
  • Recommended For Street Driven Turbo and Centrifugal Supercharger Applications
  • Supports 1,000+ HP
  • 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
  • Snow Performance Hyper-Sonic Water Methanol Nozzle
  • Snow Performance ACU-SEAL™ Water Methanol Compression Fittings
  • Snow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol Pump
  • Snow Performance Running "S" Engraved Low Profile Nozzle Holder
  • Snow Performance Running "S" Engraved Low Profile High Flow Check Valve
$459.00
Snow Performance Stg 2.5 Boost Cooler F/I Prog. Water / Meth Injection Kit (SS Braided Line 4AN Fittings) (Snow210BRD)
Unlock 50-80HP on your boosted vehicle while decreasing your air temps by up to 150 degrees!

The all new Snow Performance Stage 2 Boost Cooler® water-methanol injection system comes fully revamped in 2015 for all boosted (turbocharged/supercharged) vehicles and uses a progressive gauge style controller that proportionally injects more or less according to boost pressure.

Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. Taking it one step further, the Stage 2 has the ability to progressively command 2 Hyper-Sonic™ Nozzles independently of one another. This sophisticated dual stage injection management yields the highest increases in HP and cooling along all stages of the engine allowing you to greatly increase the boost & timing of your vehicle safely. Proven to deliver 50-80 HP and cool inlet temps up to 150 degrees!

The VC-50 comes with a dual 7 color OLED screen and displays boost, percentage of injection, low level, and secondary nozzle activation directly on the screen. Complete with our industry leading Snow Performance 300 PSI UHO pump and Hypersonic Nozzles, the Stage 2 promises to deliver the best atomization and power available for your boosted vehicle.

Kit Includes:
* 300 PSI UHO (Ultra High Output) Pump
* 3 Quart Reservoir
* All Tubing Necessary for Installation 10' ¼ Inch High Temp Nylon Tubing 18" High pressure Boost Line 3' (Black) Wire Loom
* VC-50 Controller
* Pigtail Harness
* 2 1/16 Gauge Pod
* Level Switch Upgrade
* 1 Nozzle Holder/Check Valve Combo
* 3 Hyper-Sonic™ Nozzles (175, 375, 625 ml/min) For Applications up to 1,000 HP
* Required Hardware Needed For Installation
* Snow Performance Running S Decal
* Comprehensive Instructions to Install on Any Forced Induction Vehicle
* Snow Performance 1-Year Warranty

*NOTE:* For use with all centrifugal superchargers (ProCharger, Vortech) and large turbos. For positive displacement superchargers (Eaton, Twin Screw) and small fast spooling turbos see (part# 212) Stage 2 MAF/MAP for best performance.
$591.61
Per Page      1 - 2 of 2
  • 1